ALL PRODUCTS

Showing 1 - 12 of 12 results
Bob Smith Industries Insta-Cure Super Thin 1oz
- 28%
Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting...

Hobby Building Accessories

Bob Smith Industries Insta-Cure Super Thin 1oz

$4.99 $6.99
Add To Cart
Add To Cart
Bob Smith Industries Insta-Cure Super Thin 1/2oz
- 31%
Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting...

Hobby Building Accessories

Bob Smith Industries Insta-Cure Super Thin 1/2oz

$3.30 $4.79
Add To Cart
Add To Cart
Bob Smith Industries Insta-Set Accelerator Pump 2oz
- 26%
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle...

Hobby Building Accessories

Bob Smith Industries Insta-Set Accelerator Pump 2oz

$5.15 $6.99
Add To Cart
Add To Cart
Bob Smith Industries Insta-Cure Gap Filling 1/2oz
- 19%
Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts...

Hobby Building Accessories

Bob Smith Industries Insta-Cure Gap Filling 1/2oz

$3.85 $4.79
Add To Cart
Add To Cart
Zap a Gap CA+ (Medium-Green) 1/2oz.
- 9%
SUPERIOR GAP FILLING FORMULAMEDIUM VISCOSITYALLOWS APPROXIMATELY 7 TO 10 SECONDS FOR PART POSITIONINGAVERAGE OF 20 SECONDS FOR CURINGWORKS ON OILY SURFACESUSE ZIP KICKER TO ACCELERATE CURE TIMEAVAILABLE IN 8 CONVENIENT...

Hobby Building Accessories

Zap a Gap CA+ (Medium-Green) 1/2oz.

$4.99 $5.49
Add To Cart
Add To Cart
Bob Smith Industries Maxi-Cure Extra Thick 1oz
- 27%
Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better...

Hobby Building Accessories

Bob Smith Industries Maxi-Cure Extra Thick 1oz

$5.10 $6.99
Add To Cart
Add To Cart
Bob Smith Industries Maxi-Cure Extra Thick 8oz
- 36%
Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better...

Hobby Building Accessories

Bob Smith Industries Maxi-Cure Extra Thick 8oz

$22.75 $35.99
Add To Cart
Add To Cart
Bob Smith Industries Insta-Set Accelerator 8oz
- 21%
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle...

Hobby Building Accessories

Bob Smith Industries Insta-Set Accelerator 8oz

$10.99 $13.99
Add To Cart
Add To Cart
BSI Extender Tip- #301
- 30%
For use over BSI's standard #312 top. Can be used with all thicknesses of CA except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that...

Hobby Building Accessories

BSI Extender Tip- #301

$2.07 $2.99
Add To Cart
Add To Cart
Bob Smith Industries Maxi-Cure Extra Thick 1/2oz
- 31%
Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better...

Hobby Building Accessories

Bob Smith Industries Maxi-Cure Extra Thick 1/2oz

$3.30 $4.79
Add To Cart
Add To Cart
BSI Extra Long Extender Tip - #303
For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very...

Hobby Building Accessories

BSI Extra Long Extender Tip - #303

$1.00
Add To Cart
Add To Cart
BSI PTFE Tubing - #305
- 31%
Two foot length of tubing can be cut off to any length (usually 2"). With one end cut at a 45° angle, can be inserted 1/8" into Pocket CA top...

Hobby Building Accessories

BSI PTFE Tubing - #305

$2.18 $3.17
Add To Cart
Add To Cart
img

Added to cart successfully!